What angle of inclination of the solar panel to choose to have the best production over the whole year?
To best optimize the production of solar panels, do not underestimate the importance of their orientation and inclination! However, it’s not always about producing a maximum amount of energy; you also need to take into consideration your consumption needs.
For instance, if you are self-consuming your electricity rather than selling it back to the grid, the optimal orientation is not necessarily the same!
Why is the tilt of the panels so important?
The tilt of the panels is important because your panels will produce a maximum of energy when the sun is directly perpendicular to them. During the winter in the northern hemisphere, for example, the sun is low in relation to the horizon. In this case, for the solar panels to get their best performance, a steep angle of 60° is best.
During the spring the best angle is 45°, and during the summer when the sun is high in the sky, it’s best to have a low tilt at 20°!
What angle for solar panels should be chosen to maximize the production all year long?
In solar thermal energy
The aim is to produce more heat in the winter and less heat in the summer. Example: In Marseille, for conventional thermal energy, 4m² of panels are necessary for a typical home’s hot water needs (200 L at 45 ° C) and the best inclination of the panels is between 50° and 55°.
This inclination does not correspond to maximum sunshine, but because there is a surplus of production in the summer, it is better to optimize the angle for the winter.
Photovoltaic (PV)
For photovoltaic panels where the electricity is re-injected into the grid for re-sale , the optimum orientation is south with an angle of a 37°, which maximizes total electricity production.
PV -T
With the DualSun PV- T panels, which produce both electricity and hot water, the optimal angle is the same as for PV panels.
Example: For a DualSun installation in Marseille, we recommend a 4-panel design for a family of 4. The best angle for that is maximum sunshine (37 °).
Some panels are installed on the façade of a building. Does this make sense?
Solar panels installed vertically produce less energy, but a façade installation can still make sense depending on the specific needs and constraints of the building. For example, the Arpont shelter has DualSun panels installed vertically. This was a design choice, but also a technical decision to avoid an accumulation of snow during the winter.
What impact does the angle have on production as we diverge from the “ideal angle”?
From : www.energieplus-lesite.be
You can see on the graph above the variation of sunlight according to the orientation and tilt on a given surface. Note that the slope is important, but the orientation is essential as well!
Does it make sense to adapt the tilt of a roof to optimize production?
In the case of PV-T, when a roof has a fixed slope, it is not necessary to change the angle of the roof to get an optimal production. In fact, the production of energy will always be interesting (which is not necessarily true with thermal solar panels for heating).
Why is the orientation of the panels important?
The orientation of the panels is important to capture a maximum of sunlight and therefore produce a maximum of energy.
On a fixed installation, what direction is best to have the best production?
South-facing roofs receive the most sunlight, and therefore the most solar energy during the day.
What will be the impact on production if it derives from this ideal orientation?
If you refer to the diagram above, you will see that further you are from the south, the more your production will be affected.
Does it ever make sense to have panels east/west facing rather than south-facing?
In the case of “self-consumption” for the PV production, it can make sense to orient the panels east/west rather than south-facing. East-facing panels will produce more energy in the morning, west-facing more energy in the late-afternoon. With respect to energy autonomy, the goal is not to produce the maximum but what is needed.
This is, for example, the case for the off-grid Arpont chalet in the French Alps, where the DualSun panels are oriented east/west to be able to produce more energy in the morning and the evening and less during the day, when the shelter is pretty empty!
Hi
Would you please say that what is the best angle for sunlight to collide with solar panel?
Is it 90 degree and it should be vertically or it should have afew degree to reflect from surface of panel?
Hello, I let you consult this article which will answer your questions : Why should thermal panels be inclined more than photovoltaic panels? https://academy.dualsun.com/hc/en-us/articles/360005275740-Why-should-thermal-panels-be-inclined-more-than-photovoltaic-panels-
Thanks for your interest !
I’m using your recommended tilt angles to optimize autumn, winter and spring. Thank you. In summer my consumption is low so the spring setting is fine.
In winter and other seasons, I want power in the morning and afternoon. I don’t use a lot of power at noon.
I want to point half the PVs 15 degrees to the east and the other half to the west. I have only one MPPT to control the 6+6 panels..I’m at 26 degrees south. There is no shading.
Please may I have your opinion or point me to an URL.
You want a perpindicular collision angle, so yes 90 degrees. The trouble is this means a steeper angle in winter and a shallow angle in summer, so the ideal angle is really somewhere in the middle, based on the angle the sun is at during an equinox at the latitude you’re building for.
Just wondering if it would be smarter overall to optimise for winter when there is less input available and accept a lower efficiency in the summer but probably more output anyway?
He did not ask anything about thermal panels! He asked about optimum solar angle. If the panels are fixed, the optimal orientation is south facing, with a degree angle 90 degrees to the solar equinoxes. Meaning, the panels face midway between the solar maximum and minimum angles to maximise gain.
Hello, where can I find more info about hybrid pv/t such as back insulation thickness,absorbtion surface etc ?
Thank you
Hello,
You can read this article about the insulation of our solar panel: https://academy.dualsun.com/hc/en-us/articles/360005276440-What-is-the-difference-between-the-non-insulated-and-insulated-versions-of-our-panels- Good continuation and thank you for your interest!
My place is in northern ca. And my latitude is 42 degrees and my roof facing south.
What angles would be the best for optimal
This is really appreciated that you have presented this data over here, I love all the information shared. It will be very helpful to understand the content of what is the optimal orientation and tilt angle for solar panels.
Thanks to the author for sharing such a great post. The article was very well written and providing what is the optimal orientation and tilt angle for solar panels. It can be really great for people like me who are looking for grabbing more knowledge about it.
Such a nice blog on what is the optimal orientation and tilt angle for solar panels This article is one of the beautiful articles which attracts me a lot. I enjoyed a lot while reading this article and would suggest others too and get the best options. You have done an excellent job with this content I must say.
It was helpful when you explained that south-facing roofs are the best place for fixed solar panel installation since they get more sunlight. I just learned that my daughter and her husband want to have solar panels installed on their single-family home to pursue a more sustainable lifestyle. Maybe I’ll send them this article so they can ask the right questions about orientation to find a knowledgeable installation service for the solar panels!
Thanks for explaining what makes the ideal angle for solar panels. My husband and I want to have solar panels installed soon. I’m glad di learned what factors we need to discuss with a contractor before the installation.
This concept is very good which give us information regarding what is the optimal orientation and tilt angle for solar panels. It is a pleasure worth reading this article. I enjoyed reading this article and would suggest others to come In this particular blog and get all the information regarding it.
Phoenix AZ area (33.65 N latitude). I want to mount some solar panels on 5/12 pitch roof that faces 303 deg (almost NW), and tilt one edge of the panels (the edge facing 33 deg NE) upwards so the effective direction it faces is 270 deg (due W). How can I calculate the angle to lift one edge considering the roof angle and the roof orientation to achieve any final panel orientation?
Is it okay to place panels at 180° inclination?